- #Vmware esxi 6.7 with agentless management service install
- #Vmware esxi 6.7 with agentless management service drivers
Just need to add your choice of SSDs and cable up to B120i port. I could not find it on Amazon US site but there was one from CableCreations that same length. The 50cm cable from Jyopto works great and not too much spare to lose within the system.
This is an SFF-8087 Mini-SAS connector to 4 SATA header cables. The final part of the puzzle is another Mini-SAS to SATA cable the same as the one connected to the internal drive bays. Bracket is then fixed in place using the provided screws (see photo). This leaves enough metal for screws to thread in.Ĭheck and measure each hole against the bracket as you go so that they line up. I used two strips on to stop the drill bit from walking across the metal. Put some insulating tape along the underneath of the upper chassis rail next to the PSU and drilled three small holes. I mounted the bracket next to the PSU but leaving a 2-3mm gap to allow for some airflow past the SSDs in case they get warmed by the P222. The bracket holds two SSDs and provides a small gap between them. Two types of power splitter cables are included along with two SATA cables. The kit comes with all the cabling you need and all the required screws to mount the drives and bracket. Sabrent 3.5" to x2 SSD Internal Mounting Kit (BK-HDCC) This is pretty much my ideal setup for a stable resilient but small server. The outcome is a server with a mirrored system drive on the internal B120i, and the main drive bays connected to an HP P222 card providing a RAID-10 data volume. I must admit I am rather pleased with the end result of this project and may repeat it on the other Gen8 MicroServer. and managed to find the bits needed on Amazon! I had to look around to see what alternatives I could find. A shame I am on the wrong side of the Atlantic to order an SDM kit as the import duties make it an expensive option, or would have if they were still available.
#Vmware esxi 6.7 with agentless management service drivers
I was wondering if installing HP Custom Image 6.5U2 with the drivers Agentless Management Service working and doing a full upgrade to ESXI 7.0 would do the trick, since its an upgrade not a clean install.so libraries should stay supporting older drivers installed.ĭoes this make any sense? Has anyone gone trough this alredy?Īll credit to schoondoggy for his original idea.
#Vmware esxi 6.7 with agentless management service install
Install Vmware ESXI HP Custom Image 6.5U2 -> Offline Update to Vmware ESXI 6.7. But I´ve been reading lots of people having working setups doing the following: Makes sense following the Vmware ESXI HPE support matrix, since its only supported until Vmware ESXI 6.5U2 Pre-gen. opt/hpe/ams/amshelper: error while loading shared libraries: libnicmgmt.so.0: cannot open shared object file: No such file or directory With that context being said, Im trying to enable the Agentless Management Service from the ILO with the drivers on the Vmware ESXI 7, but unfortunetly after installing and trying to start the service with: I have a Microserver Gen 8 with Vmware ESXI 7 currently installed on the MicroSD with AHCI enabled instead of RAID mode (dont find anything usefull in raid mode in my current setup other than booting from ODD, which I can just use as another Datastore instead). I have a question I was wondering if someone would know about. Issue the following commands to enroll all keys on your deb-based system:įantastic! Thanks! You are a champion! ? Subscribe Deb-based systems to the mcp repositoryĬut-n-paste the following section (substituting distribution, architecture and project version) into /etc/apt//mcp.list on your system:ĭist buster, bionic, xenial, trusty, precise, stretch, jessie, squeeze - hp-ams is in jessie Gen9 users, please use "10.xx" or earlier. Gen10 users, please subscribe to "11.xx" or "current" repositories. The hp-health, hp-snmp-agents, hp-smh* and hp-ams debs are only to be installed on Gen9 servers and earlier. NOTICE: The health/snmp functionality was moved to the iLO card on HPE ProLiant Gen10 servers. Ssa HPE Array Smart Storage Administration Service Ssaducli HPE Command Line Smart Storage Administration Diagnostics Ssacli HPE Command Line Smart Storage Administration Utility Hp-smh-templates HPE System Management Homepage Templates (Gen9 and earlier) Hpsmh HPE System Management Homepage (Gen9 and earlier) Hp-snmp-agents Insight Management SNMP Agents for HPE ProLiant Systems (Gen9 and earlier) Hp-ams HPE Agentless Management Service (Gen9 and earlier) Hponcfg HPE RILOE II/iLO online configuration utilityĪmsd HPE Agentless Management Service (Gen10 only) Hp-health HPE System Health Application and Command line Utilities (Gen9 and earlier) I have some notes but dont remember what they mean